CMM Programmer - 1st Shift Aerospace Manufacturing - CPP- Rancho Cucamonga
Rancho Cucamonga, CA
About the Job
JOB SUMMARY
The Dimensional/Layout Inspector / Computerized Measuring Machine (CMM) Programmer Level I carries out the following responsibilities: Run CMM pre-existing programs, create new Part programs, ability to read blue prints, Interprets Geometric Dimensions and Tolerances, and able to inspect product on open setup.
ESSENTIAL JOB FUNCTIONS/DUTIES
This position requires use of information or access to hardware which is subject to the International Traffic in Arms Regulations (ITAR). All applicants must be U.S. persons within the meaning of ITAR. ITAR defines a U.S. person as a U.S. Citizen, U.S. Permanent Resident (i.e. 'Green Card Holder'), Political Asylee, or Refugee.
It is the policy of CPP Corporation to cooperate to the fullest extent with the applicable regulations of the Civil Rights Act and any legislation on Equal Employment Opportunity. CPP Corporation is an Equal Opportunity Employer that recruits, hires, trains, and promotes employees in all job classifications without regard to race, color, religion, age, sex, sexual orientation, gender identity, marital status, national origin, disability, veteran's status, or other legally protected status.
EOE/M/F/DISABLED/VETERANS
The Dimensional/Layout Inspector / Computerized Measuring Machine (CMM) Programmer Level I carries out the following responsibilities: Run CMM pre-existing programs, create new Part programs, ability to read blue prints, Interprets Geometric Dimensions and Tolerances, and able to inspect product on open setup.
ESSENTIAL JOB FUNCTIONS/DUTIES
- Perform visual and dimensional inspection of castings to determine conformance to blue print, or electronic file requirements.
- Ability to interpret geometrically dimensioned and tolerance engineering drawings.
- Perform First Article Inspection Reports using AS9102 Forms as required.
- Work from and with dimensional inspection measurement equipment such as surface plate, sine plates, height gages, radii gages, calipers, micrometers and other assorted hand measurement equipment.
- To perform the CMM Operator job successfully, an individual must be able to perform each essential responsibility satisfactorily. These requirements are representative, but not all – inclusive, of the knowledge, skill, and ability required of this position. Reasonable accommodations may be made to enable individuals with disabilities to perform the essential functions.
- Education: High school diploma or general education degree (GED)
- Experience: Utilization of both CMM and hand equipment to perform dimensional inspection techniques.
- Certifications/Licenses: AFS Laboratory Certification Preferred.
- Other Required Knowledge, Skills & Abilities:
- Computer Skills: Virtual Dimensional Measuring Interface Specification (DMIS) 6.0, Virtual DMIS, Routine CMM Operation, Geometric Dimensioning and Tolerance,
- Expert PC-DMIS Knowledge required.
- Polyworks And Bluelight scanning a plus.
- Software experience; Excel, Word, Power Point, etc.
- Ability to read blue prints in order to determine and measure features and tolerances.
- Ability to interpret reduced dimension drawings
- Ability to program using electronic model
- Surface Plate Inspection using Standard Inspection Tools
- Knowledge of Aerospace Standard (AS) 9100 requirements
- Bilingual – English/Spanish a Plus
This position requires use of information or access to hardware which is subject to the International Traffic in Arms Regulations (ITAR). All applicants must be U.S. persons within the meaning of ITAR. ITAR defines a U.S. person as a U.S. Citizen, U.S. Permanent Resident (i.e. 'Green Card Holder'), Political Asylee, or Refugee.
It is the policy of CPP Corporation to cooperate to the fullest extent with the applicable regulations of the Civil Rights Act and any legislation on Equal Employment Opportunity. CPP Corporation is an Equal Opportunity Employer that recruits, hires, trains, and promotes employees in all job classifications without regard to race, color, religion, age, sex, sexual orientation, gender identity, marital status, national origin, disability, veteran's status, or other legally protected status.
EOE/M/F/DISABLED/VETERANS
Source : CPP- Rancho Cucamonga
